Concrete Footing Calculator
Find how much concrete you need for strip, pad, or pier footings. Enter your footing dimensions and get the cubic yards, bags, and cost in seconds, with a waste allowance built in.
A concrete footing calculator works out how much concrete a footing pour needs, in the two units that matter: cubic yards for a ready-mix order, and bags for a smaller mixed-by-hand job. Footings come in a few shapes, and each is measured differently, which is where a single volume formula falls short and a shape-aware calculator earns its place.
This calculator covers the three footings most projects use: continuous strip footings under walls, isolated pad footings under posts and columns, and round pier or sonotube footings for decks and porches. Pick the type, enter the dimensions, and it returns the cubic yards, the bag count for your chosen bag size, and an optional cost, with a waste allowance for over-excavation and spillage. It estimates material only; footing size, depth, and reinforcement are set by your local code, not by this tool.
A concrete footing calculator works out how much concrete a footing pour needs, in the two units that matter: cubic yards for a ready-mix order, and bags for a smaller mixed-by-hand job. Footings come in a few shapes, and each is measured differently, which is where a single volume formula falls short and a shape-aware calculator earns its place.
This calculator covers the three footings most projects use: continuous strip footings under walls, isolated pad footings under posts and columns, and round pier or sonotube footings for decks and porches. Pick the type, enter the dimensions, and it returns the cubic yards, the bag count for your chosen bag size, and an optional cost, with a waste allowance for over-excavation and spillage. It estimates material only; footing size, depth, and reinforcement are set by your local code, not by this tool.
How to Use This Calculator
Step 1: Choose the footing type
Select Strip for a continuous footing under a wall, Pad for isolated rectangular pads under posts or columns, or Pier for round holes and sonotube footings under decks and porches. The inputs and the diagram change to match.
Step 2: Enter the dimensions
For strip and pad, enter length, width, and thickness, each with its own unit (length is usually in feet, width and thickness in inches). For pads, add the number of pads. For piers, enter the diameter, the depth, and the number of piers. Use the actual concrete dimensions, not the hole size if you are over-digging.
Step 3: Pick the bag size (advanced)
The default is the 80 pound bag, the most common for footings. Switch to 60 or 40 pound in the advanced section if that is what you are buying, and the bag count updates.
Step 4: Set the waste factor (advanced)
Keep 10 percent for typical trench and pour conditions. Raise it for rough excavation, soft or uneven trench bottoms, or hand-dug holes that are wider than planned, all of which swallow extra concrete.
Step 5: Add cost (optional)
Enter a price per cubic yard for ready-mix (commonly around $120 to $200 per yard) or per bag, and pick the matching basis. The calculator applies it to the right quantity.
Reading the results
Concrete Volume in cubic yards is your ready-mix order; the bag count is for mixing by hand. If the bag count climbs past about 45 (one yard), ready-mix is usually the better buy. Always order a little extra, since running short mid-pour creates a cold joint. Use the copy button to save the figures.
How the Calculation Works
Every footing estimate is a volume calculation: work out the cubic feet of the footing, add waste, then convert to cubic yards and bags. Only the volume step changes with the shape.
Strip and pad footings (rectangular)
Volume = Length × Width × Thickness
All three in feet. A strip footing is one continuous run (quantity 1); a pad footing multiplies by the number of identical pads. A 20 foot strip footing 16 inches wide and 8 inches thick is 20 × 1.333 × 0.667 = about 17.8 cubic feet.
Pier and sonotube footings (cylindrical)
Volume = π × (Diameter / 2)² × Depth × Quantity
A round pier is a cylinder. Six 12 inch piers each 42 inches deep: π × 0.5² × 3.5 × 6 = about 16.5 cubic feet.
Add waste
Order volume = Volume × (1 + waste)
The default 10 percent covers over-excavation, uneven trench bottoms, and spillage. 17.8 × 1.10 = about 19.6 cubic feet.
Convert to cubic yards
Cubic yards = Order volume / 27
There are 27 cubic feet in a cubic yard, the unit ready-mix is sold in. 19.6 / 27 = 0.72 cubic yards.
Convert to bags
Bags = round up (Order volume / bag yield)
An 80 pound bag yields about 0.60 cubic feet, a 60 pound bag about 0.45, and a 40 pound bag about 0.30. At 0.60: 19.6 / 0.60 = about 33 bags. As a shortcut, one cubic yard takes about 45 bags of 80 lb, 60 bags of 60 lb, or 90 bags of 40 lb.
Cost (optional): Cost = cubic yards × price per yard, or bags × price per bag, matching how you are buying.
Worked Example
Scenario: A continuous strip footing for a garage
You are pouring a strip footing around a detached garage with a total run of 40 feet, 18 inches wide and 10 inches thick, using a 10 percent waste allowance, and pricing ready-mix at $160 per cubic yard.
Step 1: Volume in cubic feet
Convert width and thickness to feet: 18 inches = 1.5 feet, 10 inches = 0.833 feet.
40 × 1.5 × 0.833 = 50 cubic feet
Step 2: Add 10% waste
50 × 1.10 = 55 cubic feet
Step 3: Convert to cubic yards
55 / 27 = 2.04 cubic yards
Step 4: Bag equivalent
55 / 0.60 = 91.7, rounded up to 92 bags of 80 pound mix
Step 5: Cost
2.04 × $160 = about $326 in ready-mix
Final estimate: About 2.04 cubic yards, roughly $326 delivered. The bag equivalent, 92 bags, is the tell that this is a ready-mix job: mixing 92 bags by hand would take many hours and risk inconsistent concrete, and at typical bag prices it would also cost more than the $326 ready-mix. For a small job like a handful of deck piers the bag count would be low enough to mix yourself, but a continuous garage footing belongs on a truck. Remember this figure is concrete only; the footing’s width, thickness, depth below frost, and rebar come from your local code.
Understanding the Variables
Footing Type
Selects the geometry. Strip is a continuous footing under a wall, measured as one long run. Pad is an isolated rectangular footing under a point load (a post or column), measured per pad and multiplied by the count. Pier is a round, vertical footing (often poured in a sonotube) for decks, porches, and posts, measured as a cylinder.
Length, Width, and Thickness (strip and pad)
The three dimensions of a rectangular footing. Length is the run (the full perimeter length for a strip footing); width is the footing’s face width; thickness is how deep the concrete itself is, not how far below grade the trench sits. Each has its own unit, since length is usually in feet while width and thickness are in inches.
Number of Pads (pad type)
How many identical pad footings you are pouring. The calculator multiplies one pad’s volume by this count. For pads of different sizes, run each size separately and add the results.
Diameter, Depth, and Number of Piers (pier type)
The diameter of the round footing or tube, the depth (full height of concrete in the hole or tube), and how many you are pouring. Pier volume grows with the square of the diameter, so a small increase in diameter adds noticeably more concrete. If your tube form has a flared or belled base, add that volume separately from the manufacturer’s spec sheet.
Bag Size (advanced)
The mix bag you plan to buy, which sets the bag count. Standard estimating yields are about 0.60 cubic feet for an 80 pound bag, 0.45 for a 60 pound bag, and 0.30 for a 40 pound bag, so it takes roughly 45, 60, or 90 bags respectively to make one cubic yard. Yields vary slightly by brand, so check the bag.
Waste Factor (advanced)
The allowance for over-excavation, uneven trench bottoms, spillage, and ordering safety. Ten percent is a sound default for footings; raise it for rough or hand-dug excavation where the actual hole ends up larger than planned. Footings are unforgiving of a short pour, so erring high is wise.
Concrete Cost
An optional price, entered per cubic yard for ready-mix or per bag for bagged mix, with a matching basis selector. As rough ranges, ready-mix commonly runs about $120 to $200 per cubic yard, and an 80 pound bag a few dollars each. Affects only the cost output.
Industry Standards & References
IRC Section R403 (Footings)
The International Residential Code sets the baseline for residential footings: minimum widths and thicknesses by load and soil, the requirement that footings bear on undisturbed or compacted soil, and the rule that they extend below the frost line. Building departments check footing work against R403, and footing sizing tables in the code are tied to presumptive soil bearing values.
Frost depth
Footings must sit below the local frost line so that freezing and thawing soil cannot heave them. Frost depth ranges from essentially zero in the far south to 48 inches or more in northern states; in frost-free areas a minimum of 12 inches below grade is typical. This depth governs how deep the hole is, separate from how thick the concrete footing itself is.
Soil bearing capacity
How wide a footing must be depends on the load above and the soil’s presumptive load-bearing value (for example, the code assigns lower values to soft clays than to gravel or sandy gravel). A footing spreads the structure’s load over enough soil area to stay within that value, which is why footing width is an engineering decision, not a rule of thumb.
ACI 318 and ACI 332
ACI 318 is the structural concrete code governing footing design and reinforcement; ACI 332 covers residential concrete specifically. These standards (and local code) determine rebar size, placement, and concrete strength, none of which a volume estimate addresses.
Concrete strength (PSI)
Footings are typically specified at a minimum compressive strength in the range of 2,500 to 3,000 psi for residential work, higher where the concrete is exposed to freeze-thaw or de-icing salts. Your mix or ready-mix order should state the required strength for the application.
Call 811 before digging: as with any excavation, contact the 811 one-call service to locate buried utilities before digging footing trenches or pier holes. It is free and required in most jurisdictions, and it prevents dangerous, costly strikes on gas and electric lines.
Frequently Asked Questions
Multiply the footing's length, width, and thickness in feet to get cubic feet, add about 10 percent for waste, then divide by 27 for cubic yards or by the bag yield for bags. A 20 foot strip footing 16 inches wide and 8 inches thick needs about 0.72 cubic yards, or 33 bags of 80 pound mix. The calculator above handles strip, pad, and pier shapes automatically. For a floor or patio instead, use our concrete slab calculator.
A strip footing runs continuously under a wall to spread its load along the length. A pad footing is an isolated rectangular base under a single point load, like a post or column. A pier footing is a round, vertical column of concrete, often poured in a sonotube, used for decks, porches, and elevated structures. Each is measured differently, so the calculator has a mode for each.
Deep enough to bear below your local frost line, which ranges from about 12 inches in mild southern climates to 48 inches or more in cold northern states. This is set by code to stop frost heave, and it is separate from how thick the concrete footing is. Our concrete footing size guide covers depth and width in detail.
It depends on the load above and the soil's bearing capacity, so it is an engineering decision rather than a fixed number. As a common residential starting point, a footing is often about twice the width of the wall it supports, but soft soils need wider footings. Always confirm the size against your local code or an engineer before pouring.
Once the job passes roughly one cubic yard, or about 45 bags of 80 pound mix, ready-mix delivery is usually the better choice. Mixing dozens of bags by hand is slow, physically demanding, and risks weak, inconsistent concrete from uneven batching. For small pours like a few deck piers or a single pad, bagged mix is practical and lets you batch precisely. Our guide to how much concrete you need walks through the yards and bags math.
Residential footings are commonly specified at 2,500 to 3,000 psi, with higher strengths where the concrete faces freeze-thaw cycles or de-icing salts. Standard bagged concrete mixes and ready-mix both meet these ranges; confirm the required strength for your application and climate, and state it when ordering ready-mix.
Deck footings are usually round piers, so use the pier mode: enter the diameter, the depth, and the number of piers. As an example, six 12 inch piers 42 inches deep need about 0.67 cubic yards, or 31 bags of 80 pound mix. If you are still planning the deck itself, our deck calculator estimates the boards and framing above the footings.
No. It estimates concrete quantity only. The size, depth, reinforcement, and concrete strength of a footing are structural decisions that depend on the load, the soil, and your local frost line, and they must follow the building code or a structural engineer's design. Never substitute a material estimate for proper footing design.
